good afternoon friends we continue to build lamborghini on the channel auto kettles today you see the manufacture of the case of our lambs everyone enjoy watching and don't forget to subscribe to our channel and like the last video link you will find in the description we showed how and but paper polygons and now we we will make the same polygons but with panerai let gluing the paper model but transfer the polygons to plywood and cut out the horror I plan our polygons for better detailing of the front rear bumper our bumper section was made by 5 centimeters the width of the lamborghini is almost two meters it is easy to calculate what front bumper polygons are needed 40 pieces if the wallet needed only twenty pieces and could be mirrored on plywood, then plywood models had to be done as a result, they cut out 40 polygons of the front bumper and 40 polygons of the rear bumper, cutting each model separately with a jigsaw is not very difficult, but it takes some time to coordinate polygons separately front ba mper and rear palette separately at the same time do not forget the model numbers, otherwise it takes a lot of time to find a suitable model we glue the models through pieces of foam you now see the models of the rear bumper because at first we did not mark our model gluing was more like looking for late models suitable now large and I didn’t make such a mistake, I hope you have already liked this video and subscribed to our channel and clicked on the bell so as not to miss a new video and find out how it turned out found the lamp as you can see now we mark our models before cutting Cutting a model diagonally takes a lot it took about two hours to transfer 80 models of the front and rear bumper to plywood and it took four days to cut it, while during the transfer we tried to use expensive plywood as economically as possible also saving oner I slowed down the cutting of our models to work with a jigsaw did not need any special skills but hands were very tired, therefore, in order to h in order to cut, we invited all our friends who were interested in firstly to see how the author of the lamborghini was somehow or something to help cut out of plywood from early morning until late at night and this is only the front and rear bumpers, and we had to do the whole lamborghini, or rather, weight and body, but we were not upset, we wanted to finish this stage as quickly as possible, although there was still a lot of time before finishing with this stage, since it was necessary to glue and then fill our models with foam to save time and expensive plywood, we decided do it diagonally not every 5 centimeters, but every 10 centimeters, we calculated that it will take a third less time, while the foam will lie down, it’s also unclear how, since the space of 5 centimeters, it behaved ambiguously, but how it will lie down, the space between ten centimeters can be seen in the next video, therefore, we decided to fill these 10 centimeters with polystyrene foam and after that already establish m mounting foam so that it will be possible to safely tie the mounting foams and the mounting foam will lie on some kind of base pieces of plywood paper polygon or pieces of mounting foam turned our garage into a trash bin again and we perfectly understood that we would have to clean up a lot after we finished the body of our lamborghini in four days they cut out the bumper, glued it and began to prepare to fill the mounting foam, the space between the colleague 0 me , well, since you already liked and subscribed to our channel, put the bell, so we continue unexpectedly, the mounting foam behaved even small portions of the foam did not expand in any way and we added foam more than anyone, the moment it began to expand sharply, it was undulating and so as not to tear our entire model, we decided to wrap the entire bumper with tape, filled the pin and gradually, therefore, it took a very long time the whole process from cutting out of plywood to more channels, gluing, filling with foam took us about three weeks and this is only the front and rear bumper the whole car, I think instead of about a few months, we also noticed that mounting foam from different manufacturers behaves differently .
The foam sometimes expands, sometimes it doesn’t expand, sometimes it expands very strongly, the mounting foam is not the best material to keep the garage clean, it constantly stuck to the hands to the clothes and small pieces fell to the floor, then they expanded greatly, huge ingots of this foam were obtained. The front bumper was tied up four times with tape to to save the original appearance of our model before cropping, our model looked like a snowball that was blinded by an inept architect, you can say it was blinded by a child, but we know that our worlds will be teachers when cleaning extra mounting foam, or which we made from plywood , the next day the foam froze and we began to cut off the excess foam to plywood, it was not tr udno and we did it in 1 day, the result was encouraging after the mounting foam, it was necessary to cut it off, then putty it and bring it to the appearance of a real lamborghini, but this is a completely different story in the next part you will see behind the pressure of the lamborghini engine compartment so as not to miss new videos subscribe press click on the bell and of course like this video
